Skip to product information
Tielocken in Shetland melton in charcoal

Tielocken in Shetland melton in charcoal

QAR 3.751,00

Colours

ColorCharcoal
Size

Overcoat — known as the tielocken because of its belted fastening — which is made in London with heavy (22oz) melton of Shetland wool woven by a mill in West Yorkshire, and with sand-cast brass sliders from the West Midlands.

The tielocken is a coat style from the glory days of outerwear past. "The smartness essential in a topcoat," the old ad copy goes, "allied to such dependable powers of protection as enable the wearer to face the worst weather without discomfort or risk to health — those are the characteristics which define the tielocken."

The tielocken, then, sits between formal overcoat and full-blown, double-breasted, protective outerwear. It sure has the collar and lapel of the former — with a smart narrow notch, with, though it can't be seen here, some careful hand-stitching that keeps the join of collar and lapel flush and tidy at all times.

The tielocken has four pockets at the front: below the large flap pockets can be found in-seam pockets, stationed at just the right lateral and longitudinal coordinates for the instinctive plunging-in of hands. One additional pocket — the obligatory in-breast pocket — is on the inside of the coat.

What defines the tielocken is the absence of any buttons at the front. Instead, the wearer feeds a belt through a slider fixed on a tab, then another slider on the opposite side, and then pulls the belt as tight as desired. It is surprisingly intuitive, and as satisfying a way to fasten a coat as could be conceived.

The belt is fixed to the tielocken at either side. It thus cannot be removed. It's with you for life. No belt-loops. No way for the belt to slip around and be at an inopportune position for grabbing and fastening — let alone getting lost. It's not going anywhere.

The back of the coat can be pulled together with a double-slider system at the back, rather like the strap of a bag. You can thus wear the coat open and loose, or open and pulled together at the back in a smart and gentlemanly manner.

There's a large inverted pleat all the way up the back of the coat, too, to give shoulders more room to flex and legs more room to kick. This pleat is fixed halfway up — beneath where the belt runs — to stop it from "bagging out", as the phrase goes.

The tielocken has plain cuffs. Purely decorative, these — but what isn't? — and anyway a good and proper punctuation point to the sleeves.

One of the most novel aspects of the coat is its construction. It is a hybrid of two types of sleeve: the smart lines of a traditional inset sleeve at the front, but, at the back, a raglan sleeve. This provides great freedom of movement in the upper body: much more than a coat of this ilk would ordinarily provide.

The coat has an in-breast pocket — an internal chest pocket, that is — of the tidy jetted variety on the left side as worn.

The tielocken is lined halfway down the back with a smooth and slinky satin, cut as a single panel. It helps with sliding the peacoat on and off, being as the outer cloth has the potential for friction. The sleeves, too, are lined with the same cloth.

The cloth is a heavy woollen twill of Shetland yarn, which is characteristically tough and hairy and bristling with fuzz. It is, indeed, the yarn used traditionally for regional tweeds, and therefore the cloth has great toughness about it, repels wind and rain, and yet breathes well: great for all-weather outdoor use.

As worn

Him, here, with his chest of 38, height of 6ft 1in, and weight of 12 stone, is wearing the tielocken in size S.

Same coat, same size, same result — just worn over a sweater rather than a shirt.

Makers of

The coat is made in north-east London. It is a very specialised skill, assembling coats from heavy cloth, and every reasonable step — and the odd unreasonable step — is taken to ensure things are built to last, from the cutting of the pattern to the work on the machine, but without the results being stiff or bulky.

The wool cloth hails from a mill founded in the Heavy Woollen District of West Yorkshire in the 1800s. Carding, blending, spinning, and weaving — it all happens on the same premises. This unique arrangement means that the fleece’s change into top-grade cloth could not be more tightly tuned.

The brass hardware is made by a foundry in the West Midlands, which was founded in the 1800s. It is the last such foundry in an area once heaving with them. Its sand-casting method — which sees 940°c molten brass poured by hand from a crucible into sand-made moulds — is ancient and infallible.

The horn buttons are cut, shaped, and polished by the last horn button-makers in Britain. Relocated from the Midlands to the Cotswolds, they continue a tradition going back to the 18th century."It is no easy task,"claimed William Hutton in 1780,"to enumerate the infinite diversity of buttons made in Birmingham."

So they say

The coat has landed. It is magnificent. This has to be the coolest coat I have ever seen, let alone owned. The fit is perfect, the belt is easily adjusted, per your instructions. The weight is perfect, and the fabric so soft with a very neat drape that it wears with a regal insouciance. Thank you for your creative artistry and your manufacturing perfection.

Generous words from a gent in the States who bought the tielocken in tweed in October 2018.

I just received the tielocken — and I love it! It is unexpectedly light in the best way and drapes very nicely.

So spoke the very first person to purchase the coat, in September 2018.

The tielocken is everything I expected, and that's a lot. I'm looking forward to the temperature dropping.

Kind words by a man in France, who bought the first iteration of the tielocken, in Donegal tweed, in October 2018.

Exquisite. And despite the fact that I come from a long line of blunderers, I find the belting system to be pretty intuitive.

Feedback from a gentleman in the States, who purchased the coat in October of 2018.

You may also like